Everything below concerns system suitability. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Last reviewed on 2026-06-03. Where a claim depends on a specific study, the study is described rather than over-claimed.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
| Property | Value | Notes |
|---|---|---|
| Common abbreviation | HPLC | High-performance liquid chromatography |
| Separation basis | Differential partitioning | Between liquid mobile phase and solid stationary phase |
| Common mode | Reverse phase | Nonpolar column, polar mobile phase |
| Typical detector | UV-Vis absorbance | Widely used for compounds with chromophores |
| Typical column particle size | 2–5 µm | Smaller particles can improve resolution |
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Founded in 1984, Bio-Synthesis, Inc. was known as OCS Laboratories and was one of the first companies providing commercially available synthetic oligonucleotides to the biomedical research community worldwide. It was the first producer of commercially available synthetic DNA and became a producer of synthetic peptides in 1985, and became the only company to provide both synthetic DNA and peptide under one roof. Also in 1985 the process, now known as PCR, was discovered by Mullis et al. A key activity for Bio-Synthesis was to synthesize large number of PCR primer thus assisting and solidifying the early adoption of this now common and crucial process in biology.
Blood factors (Factor VIII and Factor IX) Thrombolytic agents (tissue plasminogen activator) Hormones (insulin, glucagon, growth hormone, gonadotrophins) Haematopoietic growth factors (Erythropoietin, colony-stimulating factors) Interferons (Interferons-α, -β, -γ) Interleukin-based products (Interleukin-2) Vaccines (Hepatitis B surface antigen) Monoclonal antibodies (Various) Additional products (tumour necrosis factor, therapeutic enzymes) Research and development investment in new medicines by the biopharmaceutical industry stood at $65.2 billion in 2008. A few examples of biologics made with recombinant DNA technology include: Many vaccines are grown in tissue cultures. Viral gene therapy involves artificially manipulating a virus to include a desirable piece of genetic material. Viral gene therapies using engineered plant viruses have been proposed to enhance crop performance and promote sustainable production.
People can also develop CJD because they carry a mutation of the gene that codes for the prion protein (PRNP), located on chromosome 202p12-pter. This occurs in only 10–15% of all CJD cases. In sporadic cases, the misfolding of the prion protein is a process that is hypothesized to occur as a result of the effects of aging on cellular machinery, explaining why the disease often appears later in life. An EU study determined that "87% of cases were sporadic, 8% genetic, 5% iatrogenic and less than 1% variant." Testing for CJD has historically been problematic, due to the nonspecific nature of early symptoms and difficulty in safely obtaining brain tissue for confirmation. The diagnosis may initially be suspected in a person with rapidly progressing dementia, particularly when it is also found with the characteristic medical signs and symptoms such as involuntary muscle jerking, difficulty with coordination/balance and walking, and visual disturbances. Further testing can support the diagnosis and may include:
In March 2003, Cambridge Antibody Technology (CAT) stated its wish to "initiate discussions regarding the applicability of the royalty offset provisions for Humira" with Abbott Laboratories in the High Court of London. In November 2004, the trial began, and in December 2004, Justice Hugh Laddie ruled for CAT. A short version of the full statement of the proceedings was released. In it Justice Laddie remarked, "Abbott was in error when it made its first royalty payment to CAT calculated on the basis that only 2% of the Net Sales was due. It should have calculated on the basis of the full royalty of just over 5% and should have paid and continued to pay CAT accordingly." Justice Laddie went on to observe "...that the construction advanced by Abbott does violence to the language of the agreements, renders them obscure and makes little or no commercial sense. For this reason CAT wins the action." Abbott was required to pay CAT US$255 million, some of which was to be passed to its partners in development. Of this sum, the Medical Research Council received US$191 million, and in addition, Abbott was asked to pay the MRC a further US$7.5 million over five years from 2006, providing that Humira remains on the market. The MRC also is to receive a further £5.1 million (sterling) in respect of past royalties.
Sources: en.wikipedia.org
An anticancer drug is coupled to an antibody that targets a specific tumor antigen (or protein) that, ideally, is only found in or on tumor cells. The biochemical reaction that occurs upon attaching triggers a signal in the tumor cell, which then absorbs, or internalizes, the antibody together with the linked cytotoxin. After the ADC is internalized, the cytotoxin kills the cancer. Their targeting ability was believed to limit side effects for cancer patients and to give a wider therapeutic window than other chemotherapeutic agents, although this promise hasn't yet been realized in the clinic. ADC technologies have been featured in many publications, including scientific journals.
UniProt is an online repository of protein sequence and annotation data, distributed in UniProt Knowledgebase (UniProt KB), UniProt Reference Clusters (UniRef) and UniProt Archive (UniParc) databases. Originally conceived as the individual ventures of EMBL-EBI, Swiss Institute of Bioinformatics (SIB) (together maintaining Swiss-Prot and TrEMBL) and Protein Information Resource (PIR) (housing Protein Sequence Database), the increase in the global protein data generation led to their collaboration in the creation of UniProt in 2002. The protein entries stored in UniProt are cataloged by a unique UniProt identifier. The annotation data collected for the each entry are organized in logical sections (e.g. protein function, structure, expression, sequence or relevant publications), allowing a coordinated overview about the protein of interest. Links to external databases and original sources of data are also provided. In addition to standard search by the protein name/identifier, UniProt webpage houses tools for BLAST searching, sequence alignment or searching for proteins containing specific peptides.
An aldehyde tag is a short peptide tag that can be further modified to add fluorophores, glycans, PEG (polyethylene glycol) chains, or reactive groups for further synthesis. A short, genetically-encoded peptide with a consensus sequence LCxPxR is introduced into fusion proteins, and by subsequent treatment with the formylglycine-generating enzyme (FGE), the cysteine of the tag is converted to a reactive aldehyde group. This electrophilic group can be targeted by an array of aldehyde-specific reagents, such as aminooxy- or hydrazide-functionalized compounds.
Sources: en.wikipedia.org
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.
Retention time is the interval between sample injection and the detector response for a given compound. It depends on the compound's interactions with the stationary and mobile phases under set conditions. Matching a retention time to a standard supports tentative identification but is not always unique.
HPLC alone can separate unknown compounds and provide retention times, but it often cannot identify them with certainty. Coupling HPLC to mass spectrometry gives mass information that improves identification. Confirmation usually requires comparison with reference standards or complementary techniques.
Validation establishes suitability for a new method, while verification confirms that a method works in a specific laboratory. Verification is often used when a validated method is adopted with existing equipment and staff. Both rely on documented acceptance criteria.