Everything below concerns stationary phase. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Last reviewed on 2025-10-09. Where a claim depends on a specific study, the study is described rather than over-claimed.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
| Property | Value | Notes |
|---|---|---|
| Common abbreviation | HPLC | High-performance liquid chromatography |
| Separation basis | Differential partitioning | Between liquid mobile phase and solid stationary phase |
| Common mode | Reverse phase | Nonpolar column, polar mobile phase |
| Typical detector | UV-Vis absorbance | Widely used for compounds with chromophores |
| Typical column particle size | 2–5 µm | Smaller particles can improve resolution |
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Cardona completed his PhD at the University of Barcelona (2000–2005), where he studied developmental biology. He then undertook postdoctoral research on Drosophila neuroanatomy at UCLA (2005–2008). Between 2008 and 2011, Cardona was a Group Leader at the Institute of Neuroinformatics, jointly run by the University of Zurich and ETH Zurich. During this period, he developed computational and image-processing methods for neural circuit reconstruction and co-founded two influential open-source platforms that have become widely adopted in the neuroscience community. Cardona joined the Howard Hughes Medical Institute (HHMI) Janelia Research Campus in 2012, serving as Group Leader until 2019. In 2019, he was appointed Programme Leader at the MRC Laboratory of Molecular Biology and Professor at the University of Cambridge, where he leads research on whole-brain connectomics, circuit development, and structure–function relationships in neural systems.
There are three amino acids with side chains that are cations at neutral pH: arginine (Arg, R), lysine (Lys, K) and histidine (His, H). Arginine has a charged guanidino group and lysine a charged alkyl amino group, and are fully protonated at pH 7. Histidine's imidazole group has a pKa of 6.0, and is only around 10% protonated at neutral pH. Because histidine is easily found in its basic and conjugate acid forms it often participates in catalytic proton transfers in enzyme reactions.
6-carboxytetrahydropterin synthase (EC 4.1.2.50, CPH4 synthase, queD (gene), ToyB, ykvK (gene)) is an enzyme with systematic name 7,8-dihydroneopterin 3'-triphosphate acetaldehyde-lyase (6-carboxy-5,6,7,8-tetrahydropterin and triphosphate-forming). This enzyme catalyses the following reversible chemical reaction. 7,8-dihydroneopterin 3′-triphosphate + H2O ⇌ 6-carboxy-5,6,7,8-tetrahydropterin + acetaldehyde + triphosphate This enzyme binds Zn2+. It is isolated from the bacteria Bacillus subtilis and Escherichia coli. The stimulation is part of the biosynthesis pathway of queuosine. The enzyme from Escherichia coli can also convert 6-pyruvoyl-5,6,7,8-tetrahydropterin and sepiapterin to 6-carboxy-5,6,7,8-tetrahydropterin. Media related to 6-carboxytetrahydropterin synthase at Wikimedia Commons 6-carboxytetrahydropterin+synthase at the U.S. National Library of Medicine Medical Subject Headings (MeSH)
The ASA is closely related to the concept of the solvent-excluded surface (also known as the Connolly's molecular surface area or simply Connolly surface), which is imagined as a cavity in bulk solvent. It is also calculated in practice via a rolling-ball algorithm developed by Frederic Richards and implemented three-dimensionally by Michael Connolly in 1983 and Tim Richmond in 1984. Connolly spent several more years perfecting the method. Implicit solvation Van der Waals surface VADAR tool for analyzing peptide and protein structures Relative accessible surface area
Sources: en.wikipedia.org
A variety of natural and synthetic inhibitors of ATP synthase have been discovered. These have been used to probe the structure and mechanism of ATP synthase. Some may be of therapeutic use. There are several classes of ATP synthase inhibitors, including peptide inhibitors, polyphenolic phytochemicals, polyketides, organotin compounds, polyenic α-pyrone derivatives, cationic inhibitors, substrate analogs, amino acid modifiers, and other miscellaneous chemicals. Some of the most commonly used ATP synthase inhibitors are oligomycin and DCCD. E. coli ATP synthase is the simplest known form of ATP synthase, with 8 different subunit types. Bacterial F-ATPases can occasionally operate in reverse, turning them into an ATPase. Some bacteria have no F-ATPase, using an A/V-type ATPase bidirectionally. Yeast ATP synthase is one of the best-studied eukaryotic ATP synthases; and five F1, eight FO subunits, and seven associated proteins have been identified. Most of these proteins have homologues in other eukaryotes.
An automated synthesis is very similar in procedure to performing a manual synthesis. The overseeing chemist decides on a target molecule then formulates the experimental plan, which is a sequential series of steps. Then, they collect the required equipment and execute the plan. The automated synthesis follows the same pathway, except that the computer devises and executes the experimental plan. However, human revision is usually still required to ensure the automated route is practical and there are no implicit steps or conditions missing from the proposed procedure. In organic synthesis, organic synthesis software is used to automate the process of identifying sequences of reactions or routes that can be used to synthesize organic compounds.
The advantage in atom economy of using NCAs for peptide formation is that there is no need for a protecting group on the functional group reacted with the amino acid. For example, the Merrifield synthesis depends on the use of Boc and Bzl protecting groups, which need be removed after the reaction. In the case of Bailey peptide synthesis, the free peptide is directly obtained after the reaction. However, unwanted and difficult to remove by-products may be formed. An N-substitution of the NCA (for example, by an o-nitrophenylsulfenyl group) can simplify the subsequent purification process, but on the other hand deteriorates the atom economy of the reaction. The synthesis of NCAs can be carried out by the Leuchs reaction or by the reaction of N-(benzyloxycarbonyl)-amino acids with oxalyl chloride. In the latter case, again the procedure is less efficient in the sense of atom economy. The following peptides were synthesized using this method by 1949:
BOP (benzotriazol-1-yloxytris(dimethylamino)phosphonium hexafluorophosphate) is a reagent commonly used for the synthesis of amides from carboxylic acids and amines in peptide synthesis. It can be prepared from 1-hydroxybenzotriazole and a chlorophosphonium reagent under basic conditions. This reagent has advantages in peptide synthesis since it avoids side reactions like the dehydration of asparagine or glutamine residues. BOP has used for the synthesis of esters from the carboxylic acids and alcohols. BOP has also been used in the reduction of carboxylic acids to primary alcohols with sodium borohydride (NaBH4). Its use raises safety concerns since the carcinogenic compound HMPA is produced as a stoichiometric by-product. PyBOP, a related phosphonium reagent for amide bond formation PyAOP, a related phosphonium reagent for amide bond formation
2-Aminoisobutyric acid is not one of the proteinogenic amino acids and is rather rare in nature (cf. non-proteinogenic amino acids). In the context of cell-free protein synthesis 2-aminoisobutyric acid is compatible with ribosomal elongation of peptide synthesis. Flexizymes and an engineered tRNA body enhance the affinity of aminoacylated Aib-tRNA species to elongation factor P. The result was an increased incorporation of Aib into peptides in a cell free translation system. Iqbal et al.. used an alternative approach of creating an editing deficient valine—tRNA ligase to synthesize aminoacylated Aib-tRNAVal. The aminoacylated tRNA was subsequently used in a cell-free translation system to yield Aib-containing peptides. Aib has been found in meteorites and some antibiotics of fungal origin, such as alamethicin and some lantibiotics.
Sources: en.wikipedia.org
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.
Retention time is the interval between sample injection and the detector response for a given compound. It depends on the compound's interactions with the stationary and mobile phases under set conditions. Matching a retention time to a standard supports tentative identification but is not always unique.
HPLC alone can separate unknown compounds and provide retention times, but it often cannot identify them with certainty. Coupling HPLC to mass spectrometry gives mass information that improves identification. Confirmation usually requires comparison with reference standards or complementary techniques.
Validation establishes suitability for a new method, while verification confirms that a method works in a specific laboratory. Verification is often used when a validated method is adopted with existing equipment and staff. Both rely on documented acceptance criteria.