A practical reference on Chromatogram: what it is, how it behaves, what the literature reports, and where the honest uncertainties sit.
Reviewed 2025-08-12. Anything still debated is marked as such rather than presented as settled.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
| Property | Value | Notes |
|---|---|---|
| Retention time RSD | ≤1% for five replicate injections | Typical criterion; method-specific limits apply. |
| Resolution | ≥1.5 between critical pair | Baseline separation is generally desired. |
| Tailing factor | ≤2.0 | Measures peak symmetry. |
| Theoretical plates | ≥2000 per column | Method-dependent; higher values indicate greater efficiency. |
| Peak area RSD | ≤2% for replicate injections | Reflects autosampler and detector precision. |
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
The psi-loop (Ψ-loop) motif consists of two antiparallel strands with one strand in between that is connected to both by hydrogen bonds. There are four possible strand topologies for single Ψ-loops. This motif is rare as the process resulting in its formation seems unlikely to occur during protein folding. The Ψ-loop was first identified in the aspartic protease family. β-sheets are present in all-β, α+β and α/β domains, and in many peptides or small proteins with poorly defined overall architecture. All-β domains may form β-barrels, β-sandwiches, β-prisms, β-propellers, and β-helices.
Depending on the column size, CIM monolithic columns are primarily used for the purification or analysis of large biomolecules which are being used for cancer gene therapy, treatment of viral infectious diseases and treatment of genetic diseases. Some types of molecules that can be successfully purified using CIM columns are pDNA, IgM, inter-alpha inhibitors, virus like particles, and diverse viruses; adenoviruses, bacteriophages, feline calicivirus, hepatitis A, lentivirus, influenza A and B, rabies virus, rotavirus, tomato and pepino mosaic virus. Since 2004, BIA Separations has organized and hosted the Monolith Summer School and Symposium (MSS) which takes place every 2 years. MSS was established as there were no dedicated conferences to this technology and to bring together the top international scientists and researchers in the area of monolith chromatography to share their experiences and innovative applications. BIA Separations home page Monolith Events
Pharmaceutical engineering is an interdisciplinary science that includes drug engineering, novel drug delivery and targeting, pharmaceutical technology, unit operations of chemical engineering, and pharmaceutical analysis. It may be deemed as a part of pharmacy due to its focus on the use of technology on chemical agents in providing better medicinal treatment. This is an extremely broad category—essentially covering all health care products that do not achieve their intended results through predominantly chemical (e.g., pharmaceuticals) or biological (e.g., vaccines) means, and do not involve metabolism. A medical device is intended for use in: the diagnosis of disease or other conditions in the cure, mitigation, treatment, or prevention of disease. Some examples include pacemakers, infusion pumps, the heart-lung machine, dialysis machines, artificial organs, implants, artificial limbs, corrective lenses, cochlear implants, ocular prosthetics, facial prosthetics, somato prosthetics, and dental implants.
Prognosis varies with the type of amyloidosis and the affected organ system. Prognosis for untreated AL cardiac amyloidosis is poor, with a median survival of six months. More specifically, AL amyloidosis can be classified as stage I, II or III based on cardiac biomarkers like Nt-proBNP and cardiac troponin. Survival diminishes with increasing stage, but recent advancements in treatments have improved median survival rates for stages I, II, and III, to 91.2, 60, and 7 months respectively. Outcomes in a person with AA amyloidosis depend on the underlying disease, organ(s) affected, and correlate with the concentration of serum amyloid A protein. People with ATTR, mutant ATTR and wild-type ATTR have a better prognosis when compared to people with AL and may survive for over a decade. Survival time is not associated with gender or age, however, some measures of reduced heart function are associated with a shorter survival time. Senile systemic amyloidosis was determined to be the primary cause of death for 70% of people over 110 who have been autopsied.
Sources: en.wikipedia.org
A simple supersecondary protein topology composed of two or more consecutive antiparallel β-strands linked together by hairpin loops. This motif is common in β-sheets and can be found in several structural architectures including β-barrels and β-propellers. The vast majority of β-meander regions in proteins are found packed against other motifs or sections of the polypeptide chain, forming portions of the hydrophobic core that canonically drives formation of the folded structure. However, several notable exceptions include the Outer Surface Protein A (OspA) variants and the Single Layer β-sheet Proteins (SLBPs) which contain single-layer β-sheets in the absence of a traditional hydrophobic core. These β-rich proteins feature an extended single-layer β-meander β-sheets that are primarily stabilized via inter-β-strand interactions and hydrophobic interactions present in the turn regions connecting individual strands.
Angiotensin-converting-enzyme inhibitors (ACE inhibitors) are a class of medication used primarily for the treatment of cardiovascular and kidney diseases. This class of medicine works by causing relaxation of blood vessels as well as a decrease in blood volume, which leads to lower blood pressure and decreased oxygen demand from the heart. ACE inhibitors inhibit the activity of angiotensin-converting enzyme, an important component of the renin–angiotensin system which converts angiotensin I to angiotensin II, and hydrolyzes bradykinin. Therefore, ACE inhibitors decrease the formation of angiotensin II, a vasoconstrictor, and increase the level of bradykinin, a peptide vasodilator. This combination is synergistic in lowering blood pressure. As a result of inhibiting the ACE enzyme in the bradykinin system, the ACE inhibitor drugs allow for increased levels of bradykinin which would normally be degraded. Bradykinin produces prostaglandin. This mechanism can explain the two most common side effects seen with ACE Inhibitors: angioedema and cough.
All CHO cell lines are deficient in proline synthesis. Also, CHO cells do not express the epidermal growth factor receptor (EGFR), which makes them ideal in the investigation of various EGFR mutations. Furthermore, Chinese hamster ovary cells are able to produce proteins with complex glycosylations, post-translational modifications (PTMs) similar to those produced in humans. They are easily growable in large-scale cultures and have great viability, which is why they are ideal for GMP protein production. Also, CHO cells are tolerant to variations in parameters, be it oxygen levels, pH-value, temperature or cell density. Having a very low chromosome number (2n=22) for a mammal, the Chinese hamster is also a good model for radiation cytogenetics and tissue culture. Being the first cell line to be used for recombinant pharmaceutical production, regulatory concerns were raised with respect to Endogenous Retroviral Sequences (ERS). CHO cells contain about 1000 of these sequences and some of them are able to direct the synthesis of Intracisternal A-type particles and C-type particles. Also, low expression of reverse transcriptase was observed. However the majority of ERS are defective (stop codons in all reading frames) and contain large deletions of a putative retroviral genome.
Sources: en.wikipedia.org
System suitability is typically performed before each batch or according to the validated method and laboratory procedure. Some long runs include periodic checks during analysis. The required frequency depends on regulatory expectations and method performance.
Retention time drift can result from changes in mobile phase composition, column temperature, pump flow, or column age. A gradual shift often points to column degradation. A sudden shift may indicate a leak, mixing error, or incorrect mobile phase.
Retention time alone cannot confirm identity because different compounds may elute at similar times. Coupling HPLC with mass spectrometry or comparing against authenticated standards increases confidence. Confirmation usually requires orthogonal data.
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.