robustness is one of those subjects where the details matter more than the headlines. This page pulls together the background, the mechanisms, and the practical points readers ask about most.
Last reviewed on 2026-08-01. Where a claim depends on a specific study, the study is described rather than over-claimed.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
| Property | Value | Notes |
|---|---|---|
| Separation principle | Differential partitioning | Analytes distribute between mobile and stationary phases. |
| Mobile phase | Liquid solvent mixture | Composition controls retention and selectivity. |
| Stationary phase | Packed column particles | Often chemically bonded silica. |
| Typical detector | UV-Vis or photodiode array | Mass spectrometry is also common. |
| Common synonym | High-performance liquid chromatography | Abbreviated as HPLC. |
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Practical HPLC testing depends on careful sample preparation and instrument maintenance. Samples may require filtration, dilution, pH adjustment, or extraction to avoid column damage and matrix interference. Mobile phases are degassed and filtered, and columns are equilibrated before injection. Common problems include peak tailing, baseline drift, ghost peaks, carryover, and co-elution of analytes. Documentation of instrument logs, calibration records, and electronic audit trails supports data integrity and traceability. Ongoing training and routine maintenance help reduce variability between analysts and laboratories.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
The reaction catalyzed by 1-aminocyclopropane-1-carboxylic acid synthase (ACS) is the committed and rate-limiting step in the biosynthesis of ethylene [20], a gaseous plant hormone that is responsible for the initiation of fruit ripening, shoot and root growth and differentiation, leaf and fruit abscission, flower opening, and flower and leaf senescence. (source) It is a pyridoxal phosphate (PLP) dependent gamma-elimination (?). In the gamma elimination, PLP acts as a sink twice (absorbing electrons from two deprotonations). Proposed steps of the reaction mechanism: Formation of the ACS-PLP Schiff Base Imine Exchange Formation of the Quinonoid Intermediate Tyrosine and PLP stabilized 3C-Ring formation Formation of the ACS-PLP Schiff Base The aldehyde of coenzyme PLP reacts to form an imine (Schiff base) linkage with the catalytic domain lysine (278) residue of ACS. Imine exchange An imine exchange occurs, and the amine nitrogen of the substrate, S-Adenosyl methionine, replaces Lys (278) in the imine linkage. (Stabilized by H bonding).
Absorption spectroscopy is spectroscopy that involves techniques that measure the absorption of electromagnetic radiation, as a function of frequency or wavelength, due to its interaction with a sample. The sample absorbs energy, i.e., photons, from the radiating field. The intensity of the absorption varies as a function of frequency, and this variation is the absorption spectrum. Absorption spectroscopy is performed across the electromagnetic spectrum. Absorption spectroscopy is employed as an analytical chemistry tool to determine the presence of a particular substance in a sample and, in many cases, to quantify the amount of the substance present. Infrared and ultraviolet–visible spectroscopy are particularly common in analytical applications. Absorption spectroscopy is also employed in studies of molecular and atomic physics, astronomical spectroscopy and remote sensing. There is a wide range of experimental approaches for measuring absorption spectra. The most common arrangement is to direct a generated beam of radiation at a sample and detect the intensity of the radiation that passes through it. The transmitted energy can be used to calculate the absorption. The source, sample arrangement and detection technique vary significantly depending on the frequency range and the purpose of the experiment. Following are the major types of absorption spectroscopy:
PABA is an intermediate in the synthesis of folate by bacteria, plants, and fungi. Many bacteria, including those found in the human intestinal tract such as E. coli, generate PABA from chorismate by the combined action of the enzymes 4-amino-4-deoxychorismate synthase and 4-amino-4-deoxychorismate lyase. Plants produce PABA in their chloroplasts, and store it as a glucose ester (pABA-Glc) in their tissues. The malarial protozoan Plasmodium only make PABA when necessary, preferring to get it from the surroundings if able to. Some bacteria, including a few found in the human microbiome, are unable to make PABA for themselves but can use PABA to make folate. A few are very efficient at the PABA-to-folate conversion despite not making their own PABA. Sulfonamide drugs are structurally similar to PABA, and their antibacterial activity is due to their ability to interfere with the conversion of PABA to folate by the enzyme dihydropteroate synthetase. Thus, bacterial growth is limited through folate deficiency.
Scaffolds are used to display the heterologous protein on the bacterial cell surface. There are various scaffolds which have been used such as outer membrane proteins, fimbriae/flagella proteins and CPX (circularly permuted OmpX). The CPX scaffold allows peptide fusion at both termini of the scaffold. OMPs are common scaffolds for bacterial display. Proteins can also be displayed on the bacterial cell surface through the use of autotransporters. Autotransporters form part of the type V secretion system. They usually have three domains: leader sequence at the N-terminal; central passenger domain; autotransporter domain at the C-terminal. The heterologous protein is inserted at the passenger domain. Another method of heterologous protein fusion is fusion with fimbriae/flagella, which are filamentous protrusions on the cell surface. There are many fimbriae on mainly Gram-negative bacteria, so displaying proteins on fimbriae is advantageous over some other surface proteins which are less numerous. A disadvantage of using fimbriae is that there is a relatively small insert size limit of 10-30 amino acids.
Sources: en.wikipedia.org
The first symptom of CJD is usually rapidly progressive dementia, leading to memory loss, personality changes, and hallucinations. Myoclonus (jerky movements) typically occurs in 90% of cases, but may be absent at initial onset. Other frequently occurring features include anxiety, depression, paranoia, obsessive-compulsive symptoms, and psychosis. This is accompanied by physical problems such as speech impairment, balance and coordination dysfunction (ataxia), changes in gait, and rigid posture. In most people with CJD, these symptoms are accompanied by involuntary movements. Rarely, unusual symptoms like the alien limb phenomenon have been observed. The duration of the disease varies greatly, but sporadic (non-inherited) CJD can be fatal within months or even weeks. Most affected people die six months after initial symptoms appear, often of pneumonia due to impaired coughing reflexes. About 15% of people with CJD survive for two or more years. The symptoms of CJD are caused by the progressive death of the brain's nerve cells, which are associated with the build-up of abnormal prion proteins forming in the brain. When brain tissue from a person with CJD is examined under a microscope, many tiny holes can be seen where the nerve cells have died. Parts of the brain may resemble a sponge where the prions were infecting the areas of the brain.
As anti-angiogenic cancer therapies have achieved widespread use, there has been increased interest in non-invasive monitoring of angiogenesis. One of the most extensively examined targets of angiogenesis is integrin αVβ3. Radiolabeled peptides containing RGD show high affinity and selectivity for integrin αVβ3 and are being investigated as tools to monitor treatment response of tumors via PET imaging. These include 18F-Galacto-RGD, 18F-Fluciclatide-RGD, 18F-RGD-K5, 68Ga-NOTA-RGD, 68Ga-NOTA-PRGD2, 18F-Alfatide, 18F-Alfatide II, and 18F-FPPRGD2. In a meta-analysis of studies using PET/CT in patients with cancer, it was shown that this diagnostic method may be very useful for detecting malignancies and predicting short-term outcomes, although larger-scale studies are needed.
Gingras research focuses on the development of experimental and bioinformatics approaches for functional proteomics, with a focus on protein-protein and proximity interactions. She applies these tools to the study of signaling pathways in health and disease and in mapping the physical organization of the dynamic proteome. Some of her work focuses on the consequence of disease-associated mutations on the interactions established by proteins. In addition to proteomics, Gingras laboratory has interest in studying human protein phosphatase and their systematic interactions and has now expanded into the field of systems biology.
The psi-loop (Ψ-loop) motif consists of two antiparallel strands with one strand in between that is connected to both by hydrogen bonds. There are four possible strand topologies for single Ψ-loops. This motif is rare as the process resulting in its formation seems unlikely to occur during protein folding. The Ψ-loop was first identified in the aspartic protease family. β-sheets are present in all-β, α+β and α/β domains, and in many peptides or small proteins with poorly defined overall architecture. All-β domains may form β-barrels, β-sandwiches, β-prisms, β-propellers, and β-helices.
The catalytic mechanism of FGE is well studied. A multistep redox reaction with a covalent enzyme: substrate intermediate is proposed. The role of the cysteine residue for the occurring conversion was studied by mutating the cysteine to alanine. No conversion was found using mass spectrometry when the mutated peptide tag was used. The mechanism shows the important role of the redox active thiol group of cysteine in the formation of f(Gly), as seen in Fig. 2. The key step of the catalytic cycle is the monooxidation of the cysteine residue of the enzyme, forming a reactive sulfenic acid intermediate. Subsequently, the hydroxyl group is transferred to the cysteine of the substrate and after hetero-analogous β-elimination of H2O, a thioaldehyde is formed. This compound is very reactive and easily hydrolyzed, releasing the aldehyde and a molecule of H2S,
Sources: en.wikipedia.org
CHO cells are the most common mammalian cell line used for mass production of therapeutic proteins such as monoclonal antibodies, used in 70% of therapeutic mAbs. They can produce recombinant protein on the scale of 3–10 grams per liter of culture. Products of CHO cells are suitable for human applications, as these mammalian cells perform human-like post-translational modifications to recombinant proteins, which is key to the functioning of several proteins. It is believed that CHO-K1 transgenic cells are characterized by higher monoclonal antibody expression at the expense of biomass accumulation, for example, based on CHO-K1, monoclonal antibody‑producing cell lines with productivity up to 6.5 grams per liter have been selected. Cell culture Drug development Preclinical development
The main building of the Institute is located at the intersection of Kremlyovskaya and Lobachevskaya streets. This four-story building built in 1953 in the style of Soviet neoclassicism under the guidance of architect A.G. Bikchentaev. The building of the museum of Kazan chemical school is located in the campus of the main university building, built in the 1830s in a classical style under the guidance of architect M.P. Corinfskiy. In 2015 construction of a large laboratory building in the campus of Alexander Butlerov Institute of Chemistry was finished. The 7-storey building housed classrooms and laboratories of departments of Alexander Butlerov Institute of Chemistry, Institute of Geology and Petroleum Technologies, Institute of Physics. The building was constructed with the support of the President of Tatarstan R.N. Minnikhanov and PSC "TAIF".
AS9100 Revision C (2009), Quality Management System – Requirements for Aviation, Space and Defense Organizations The update of AS9100 from revision B to C is largely to address the following question: "Our supplier is repeatedly late on delivery and failing to meet our requirements, how is it possible that they still have their AS9100 certificate?" That is, the AS9100C changes are driven by repeated delivery of non-conforming product and repeated late delivery by organizations that held AS9100A/B certifications. Those organizations had documented controls that conformed to the standard, however, there were insufficient processes in place to assure effectiveness of those controls. The response in this AS9100 revision is to elevate the requirements for Risk Management and to make Risk Management an integrated theme throughout the standard. A major challenge to AS9100B-compliant organizations was the new AS9100 auditing standards defined in AS9101 Revision D, which eliminates the clause-based compliance checklist and requires organizations to provide evidence of effectiveness of their systems and processes. Summary of changes between AS9100B and AS9100C:
Nycomed, a Swiss drug company which manufactures Actovegin, claims it can be used for circulation and nutrition disturbances, skin grafting, burns, and wound-healing impairment. Actovegin has also been used as a performance enhancer. It has been investigated for use in treatment of polyneuropathy in diabetes, and for stroke. One study found that when tissues suffer from hypoxia caused circulation abnormalities, Actovegin helps capillaries improve circulation by enhancing the neogenic mechanism in blood vessels. Anaphylactic shock has been observed in at least one patient treated with actovegin. There are reports suggesting that Actovegin have ergogenic ability, however one small trial found no apparent benefit from short-term use. Two studies certified Actovegin to have an anti-inflammatory effect. One of the two studies certified Actovegin to reduce Progressive muscular atrophy-induced inflammation in human cells. Another study certified Actovegin to have a positive impact on the growth of muscle cells.
Sources: en.wikipedia.org
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.
Pressure drives the liquid mobile phase through a column packed with small particles. Without pressure, flow would be very slow or stop because the packed bed resists liquid movement. Modern pumps maintain a steady flow despite the resistance.
A chromatogram is a plot of detector signal against time after sample injection. Each peak represents a compound or group of compounds eluting from the column. Retention time and peak area are the main measurements read from the plot.
HPLC testing measures the presence and amount of one or more compounds in a liquid sample. It separates mixture components and records detector responses as peaks, which are compared with reference standards. Results are usually reported as concentrations or relative percentages.