The short version of Chromatogram fits in a sentence. The long version — which is the one that helps — is below.
This page was last updated on 2025-12-10 and is reviewed periodically as new material appears.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Regulatory and pharmacopeial texts shape how HPLC testing is performed and documented. The International Council for Harmonisation provides validation guidance, while pharmacopeias publish general chromatography chapters and monographs for specific materials. Accreditation standards such as ISO/IEC 17025 address laboratory competence and traceability. Inspectors may review instrument qualification, analyst training, reference material control, and electronic records. Open questions include how best to validate methods for new complex products and how to handle automated data processing. Laboratories generally resolve these issues through risk assessment, method lifecycle management, and documented scientific justification.
In quality control laboratories, HPLC testing supports batch release, raw material checks, stability studies, and impurity profiling. A validated method defines sample preparation, instrument settings, calibration, and acceptance criteria. Analysts compare results with specifications and investigate out-of-specification outcomes before a batch is approved. Documentation includes chromatograms, integration records, audit trails, and reagent details. Because results influence product decisions, laboratories follow formal quality systems and data integrity rules. The exact tests and limits depend on the material, its intended use, and the applicable regulatory framework.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Most common for neutral and moderately polar analytes |
| Column particle size | 3–5 µm | Smaller particles improve resolution but raise backpressure |
| Mobile phase pH range | 2–8 | Silica-based columns may degrade outside this range |
| Typical flow rate | 1.0–2.0 mL/min | For analytical columns with 4.6 mm internal diameter |
| Common synonyms | HPLC, LC, high-pressure liquid chromatography | High-performance liquid chromatography is the standard expansion |
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
ATC code A10 Drugs used in diabetes is a therapeutic subgroup of the Anatomical Therapeutic Chemical Classification System, a system of alphanumeric codes developed by the World Health Organization (WHO) for the classification of drugs and other medical products. Subgroup A10 is part of the anatomical group A Alimentary tract and metabolism. Codes for veterinary use (ATCvet codes) can be created by placing the letter Q in front of the human ATC code: for example, QA10. National versions of the ATC classification may include additional codes not present in this list, which follows the WHO version. A10AB01 Insulin (human) A10AB02 Insulin (beef) A10AB03 Insulin (pork) A10AB04 Insulin lispro A10AB05 Insulin aspart A10AB06 Insulin glulisine A10AB30 Combinations === A10AC Insulins and analogues for injection, intermediate-acting === A10AC01 Insulin (human) A10AC02 Insulin (beef) A10AC03 Insulin (pork) A10AC04 Insulin lispro A10AC30 Combinations
After dendritic cells have phagocytosed pathogens, they usually migrate to the vast network of lymph vessels and are carried by lymph flow to the draining lymph nodes. Each lymph node is a collection point where APCs can interact with T cells. During the migration, DCs undergo a process of maturation: they lose most of their ability to further engulf pathogens and they mature by changing surface expression of MHC and co-stimulatory molecules, as well as increased production of cytokines. The internalized antigen is digested into smaller peptides containing epitopes, which are then presented to T cells by the MHC. B cells reside in the lymph node. Once their B cell receptor binds to an antigen, they can interact with activated helper T cells, as described above. A dendritic cell that interacts with an already-activated helper T cell can become licensed. This occurs through the interaction of co-stimulatory molecules including B7 and CD40 on the dendritic cell, with CD28 and CD40 ligand on the T cell. Only licensed dendritic cells are able to activate cytotoxic T cells. T cell licensing of dendritic cells is key for activation of cytotoxic T cells for many pathogens, although the extent to which T cell help is needed may vary. In MHC class I and class II molecules, only certain epitopes of an internalized peptide can be presented. These epitopes are termed immunodominant.
Boronate affinity chromatography consists of using boronic acid or boronates to elute and quantify amounts of glycoproteins. Clinical adaptations have applied this type of chromatography for use in determining long term assessment of diabetic patients through analysis of their glycated hemoglobin. Affinity purification of albumin and macroglobulin contamination is helpful in removing excess albumin and α2-macroglobulin contamination, when performing mass spectrometry. In affinity purification of serum albumin, the stationary used for collecting or attracting serum proteins can be Cibacron Blue-Sepharose. Then the serum proteins can be eluted from the adsorbent with a buffer containing thiocyanate (SCN−).
Cardona completed his PhD at the University of Barcelona (2000–2005), where he studied developmental biology. He then undertook postdoctoral research on Drosophila neuroanatomy at UCLA (2005–2008). Between 2008 and 2011, Cardona was a Group Leader at the Institute of Neuroinformatics, jointly run by the University of Zurich and ETH Zurich. During this period, he developed computational and image-processing methods for neural circuit reconstruction and co-founded two influential open-source platforms that have become widely adopted in the neuroscience community. Cardona joined the Howard Hughes Medical Institute (HHMI) Janelia Research Campus in 2012, serving as Group Leader until 2019. In 2019, he was appointed Programme Leader at the MRC Laboratory of Molecular Biology and Professor at the University of Cambridge, where he leads research on whole-brain connectomics, circuit development, and structure–function relationships in neural systems.
In Ethiopia, the Civil Aviation Accident Prevention and Investigation Bureau of the Ethiopian Civil Aviation Authority (ECAA), which is an agency of the Ministry of Transport and Communications, conducts aircraft accident investigations in Ethiopia or involving Ethiopian aircraft. In France, the agency responsible for investigation of civilian air crashes is the Bureau d'Enquêtes et d'Analyses pour la Sécurité de l'Aviation Civile (BEA). Its purpose is to establish the circumstances and causes of the accident and to make recommendations for their future avoidance. In Germany, the agency for investigating air crashes is the Federal Bureau of Aircraft Accidents Investigation (BFU). It is an agency of the Federal Ministry of Transport and Digital Infrastructure. The focus of the BFU is to improve safety by determining the causes of accidents and serious incidents and making safety recommendations to prevent recurrence.
Sources: en.wikipedia.org
Bodybuilders may supplement their diets with protein for reasons of convenience, lower cost (relative to meat and fish products), ease of preparation, and to avoid the concurrent consumption of carbohydrates and fats. Additionally, some argue that bodybuilders, by virtue of their unique training and goals, require higher-than-average quantities of protein to support maximal muscle growth. While the recommended dietary allowance is much less, Harvard Medical School points out in Harvard Health Publishing that this RDA (recommended daily allowance) is “the minimum amount you need to keep from getting sick — not the specific amount you are supposed to eat every day.” Protein supplements are sold in ready-to-drink health shakes, bars, meal replacement products (see below), bites, oats, gels and powders. Protein powders are the most popular and may have flavoring added for palatability. The powder is usually mixed with water, milk or fruit juice and is generally consumed immediately before and after exercising or in place of a meal. The sources of protein are as follows and differ in protein quality depending on their amino acid profile and digestibility:
Lipid vesicles or liposomes are approximately spherical pockets that are enclosed by a lipid bilayer. These structures are used in laboratories to study the effects of chemicals in cells by delivering these chemicals directly to the cell, as well as getting more insight into cell membrane permeability. Lipid vesicles and liposomes are formed by first suspending a lipid in an aqueous solution then agitating the mixture through sonication, resulting in a vesicle. Measuring the rate of efflux from the inside of the vesicle to the ambient solution allows researchers to better understand membrane permeability. Vesicles can be formed with molecules and ions inside the vesicle by forming the vesicle with the desired molecule or ion present in the solution. Proteins can also be embedded into the membrane through solubilizing the desired proteins in the presence of detergents and attaching them to the phospholipids in which the liposome is formed. These provide researchers with a tool to examine various membrane protein functions.
The Society recognizes achievements and promotes academic research through four annual awards. The Biemann Medal and the John B. Fenn Award for a Distinguished Contribution in Mass Spectrometry both are awarded in recognition of singular achievements or contributions in fundamental or applied mass spectrometry, with the Biemann Medal being focused on individuals who are early in their careers. The Ronald A. Hites Award is awarded for outstanding original research demonstrated in papers published in the Journal of the American Society for Mass Spectrometry. The Research Awards are given to young scientists in mass spectrometry, based on the evaluation of their proposed research. The Fellows of ASMS are awarded to individuals in recognition for their scientific contribution to mass spectrometry and for their contribution to the ASMS community. Journal of the American Society for Mass Spectrometry Measuring Mass: From Positive Rays to Proteins The past presidents of ASMS are:
Biomaterials are used in: Joint replacements Bone plates Intraocular lenses (IOLs) for eye surgery Bone cement Artificial ligaments and tendons Dental implants for tooth fixation Blood vessel prostheses Heart valves Skin repair devices (artificial tissue) Cochlear replacements Contact lenses Breast implants Drug delivery mechanisms Sustainable materials Vascular grafts Stents Nerve conduits Surgical sutures, clips, and staples for wound closure Pins and screws for fracture stabilisation Surgical mesh Biomaterials must be compatible with the body, and there are often issues of biocompatibility, which must be resolved before a product can be placed on the market and used in a clinical setting. Because of this, biomaterials are usually subjected to the same requirements as those undergone by new drug therapies. All manufacturing companies are also required to ensure traceability of all of their products, so that if a defective product is discovered, others in the same batch may be traced.
Sources: en.wikipedia.org
In 2004, development of an antisense therapy for spinal muscular atrophy began. Over the following years, an antisense oligonucleotide later named nusinersen was developed by Ionis Pharmaceuticals under a licensing agreement with Biogen. In December 2016, nusinersen received regulatory approval from FDA and soon after, from other regulatory agencies worldwide. As of 2020, more than 50 antisense oligonucleotides were in clinical trials, including over 25 in advanced clinical trials (phase II or III). A follow-on drug to Inotersen is being developed by Ionis Pharmaceuticals and under license to Akcea Therapeutics for hereditary transthyretin-mediated amyloidosis. In this formulation the ASO is conjugated to N-Acetylgalactosamine enabling hepatocyte-specific delivery, greatly reducing dose requirements and side effect profile while increasing the level of transthyretin reduction in patients.
Possibly the most common use of affinity chromatography is for the purification of recombinant proteins. Proteins with a known affinity are protein tagged in order to aid their purification. The protein may have been genetically modified so as to allow it to be selected for affinity binding; this is known as a fusion protein. Protein tags include hexahistidine (His), glutathione-S-transferase (GST), maltose binding protein (MBP), and the Colicin E7 variant CL7 tag. Histidine tags have an affinity for nickel, cobalt, zinc, copper and iron ions which have been immobilized by forming coordinate covalent bonds with a chelator incorporated in the stationary phase. For elution, an excess amount of a compound able to act as a metal ion ligand, such as imidazole, is used. GST has an affinity for glutathione which is commercially available immobilized as glutathione agarose. During elution, excess glutathione is used to displace the tagged protein. CL7 has an affinity and specificity for Immunity Protein 7 (Im7) which is commercially available immobilized as Im7 agarose resin. For elution, an active and site-specific protease is applied to the Im7 resin to release the tag-free protein.
AnIML Core AnIML Technique Definitions Additionally, AnIML Technique Definition Documents apply constraints to the AnIML Core and are specified by the AnIML Technique Definitions. The AnIML Core consists of a set of rules defining the structure of the XML document, providing a universal container for arbitrary analytical data. AnIML Technique Definitions describe how to use the AnIML Core to record experiments of a particular scientific discipline. There is a big similarity between the mechanisms of AnIML and the AVI format. The AnIML Core defines the data container, whereas the AnIML Technique Definitions act similar to the AVI codec. It defines how the data needs to be structured and labeled. Technique Definitions are XML documents, specified by the Technique Schema. official website AnIML on GitHub
Sources: en.wikipedia.org
HPLC testing separates and quantifies components in a liquid sample. It is used to check identity, purity, concentration, or stability. The technique works best for compounds that dissolve and are not easily vaporized.
The pump maintains a steady flow rate and pressure, which keeps retention times reproducible. Pulsation or flow errors can shift peaks and distort quantitation. Modern pumps use feedback control to reduce these variations.
HPLC alone usually separates compounds but does not always identify them. Retention time matching with a known standard provides tentative identification. Coupling HPLC to mass spectrometry adds mass information that supports structural identification.
System suitability is a set of checks performed before and during an HPLC run to confirm that the instrument and method are working as expected. It may include retention time repeatability, resolution between peaks, peak symmetry, and signal intensity. Failing suitability criteria usually invalidates the run.